Une structure constituée de treillis profilés en I est soutenue aux deux extrémités par des appuis à ressort et chargée par les efforts transversaux. Le poids propre est négligé dans cet exemple . Déterminez la flèche de la structure, le moment fléchissant, l'effort normal dans des points d'essai donnés et la flèche horizontale de l'appui du ressort.
Dans l'exemple de validation actuel, nous étudions le coefficient de pression du vent (Cp) pour les barres structurelles principales (Cp,ave ) et les barres structurelles secondaires telles que les systèmes de bardage ou de façade (Cp,local ) d'après le NBC 2020 {%}#Références à [1]]] et
Base de données de soufflerie japonaise
pour les bâtiments peu élevés avec une pente de 45 degrés. Dans la partie suivante, nous vous décrivons les paramètres recommandés pour les toitures-terrasses 3D avec des avant-toits pointus.
Dans l'exemple de validation actuel, nous examinons la valeur de la pression du vent pour le calcul général de la structure (Cp,10 ) et le calcul de structure local tel que les systèmes de bardage ou de façade (Cp,1 ) d'après un exemple de toiture-terrasse de l'EN 1991-1-4 { %/?#Refer [1]]] et
Base de données de soufflerie japonaise
. Dans la partie suivante, nous vous décrivons les paramètres recommandés pour les toitures-terrasses 3D avec des avant-toits pointus.
Les normes disponibles, telles que l'EN 1991-1-4 [1], l'ASCE/SEI 7-16 et le CNB 2015 présentent des paramètres de charge de vent tels que le coefficient de pression du vent (Cp ) pour formes de base. Le point important est de savoir comment calculer les paramètres de charge de vent plus rapidement et avec plus de précision plutôt que de travailler sur des formules normatives fastidieuses et parfois compliquées.
Un portique courbe appelé « portique de Lee » est fixé aux extrémités et chargé par une force concentrée au point A. Le ratio de flèche au point A pour les pas de charge donnés doit être déterminé. Le problème est défini selon les critères de référence non-linéaires NAFEMS.
Une plaque orthotrope carrée en couches est complètement encastrée en son point central et soumise à la pression. Comparons les flèches des coins de plaque pour vérifier l'exactitude de la transformation.
Un porte-à-faux de section en Z est entièrement fixé à ses extrémités et chargé par un moment qui, dans le cas d'un modèle en coque, est représenté par quelques efforts tranchants. Déterminez la contrainte axiale au point A (au milieu de la surface). Le problème est défini selon la norme NAFEMS.
Une structure faite de profilé en I est intégrée dans les appuis des fourches. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
The verification example compares wind load calculation on a building with a flat roof using the standard EN 1991-1-4 and using CFD simulation in RWIND Simulation. Le bâtiment est défini d'après le croquis et le profil de vitesse d'afflux est calculé selon la norme EN 1991-1-4.
Une bielle de section circulaire est supportée selon quatre cas de base de flambement selon Euler et est soumise à une force de pression. Determine the critical load.
Cet exemple de vérification est basé sur l'exemple de vérification 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
A symmetrical shallow structure is made of eight equal truss members, which are embedded into hinge supports. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. Le poids propre est négligé dans cet exemple. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Un tuyau de section tubulaire est chargé par une pression interne. This internal pressure causes axial deformation of the pipe (the Bourdon effect). Determine the axial deformation of the pipe endpoint.
A structure is made of four truss members, which are embedded into hinge supports. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. Le poids propre est négligé dans cet exemple. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Considérons la travée de barre ASTM A992 W 18×50 ainsi que les poids propre et les charges d'exploitation représentés sur la Figure 1. The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Un câble très rigide est suspendu entre deux appuis. Determine the equilibrium shape of the cable (the catenary), consider the gravitational acceleration, and neglect the stiffness of the cable. Verify the position of the cable at the given test points.
Un poteau est composé d'une section en béton (rectangle 100/200) et d'une section en acier (profilé I 200). It is subjected to pressure force. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
Un système à un degré de liberté avec un amortisseur est soumis à une force de charge constante. Determine the deflection and velocity of the dashpot endpoint in the given test time.
Une poutre courbe est composée de deux poutres de section rectangulaire. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Le pendule mathématique est composé d'une corde de poids zéro et d'un point de masse à son extrémité. The pendulum is initially deflected. Determine the angle of the rope at the given test time.
Un oscillateur simple est composé de la masse m (considérée uniquement dans la direction x) et du ressort linéaire de rigidité k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Une bande bi métallique est composée d'invar et de cuivre. The left end of the bimetallic strip is fixed, and the right end is free, loaded by temperature difference. While neglecting self-weight, determine the deflection of the bimetallic strip (free end).
Une structure en treillis est composée de trois tiges (une en acier et deux en cuivre) reliées par une barre rigide. The structure is loaded by a concentrated force and a temperature difference. While neglecting self‑weight, determine the total deflection of the structure.
Un porte-à-faux de section rectangulaire possède une masse à son extrémité. Furthermore, it is loaded by an axial force. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Une plaque rectangulaire sur appuis simples est chargée de différents types de charge. Assuming only the small deformation theory and neglecting self-weight, determine the deflection at its centroid for each load type.
Cet exemple est une modification de l'exemple de vérification 0061 ; la seule différence est que le matériau du réservoir est incompressible. An open‑ended, thick‑walled vessel is loaded by both inner and outer pressure. While neglecting self‑weight, the radial deflection of the inner and the outer radius is determined.
A two-layered, open-ended, thick-walled vessel is loaded by inner and outer pressure; therefore, there is no axial stress. En négligeant le poids propre, la flèche radiale des rayons internes et externes, et la pression (contrainte radiale) du rayon central est déterminée.
Une barre de section carrée est fixée à l'extrémité supérieure. The rod is loaded by self-weight. For comparison, the example is also modeled with the concentrated force load, the value of which is equal to the gravity. The aim of this verification example is to show the difference between these types of loading, although the total loading force is equal.